programowanie pilota centralnego

[dawid27]

hej mam voyka z 96 r chce w nim zaprogramowac pilota ( stary sie rozlecial) kupilem takiego samego jak mialem macie moze intrukcje jak zaprogramowac ?
dodam ze znalazlem instrukcje ale w niej pisze aby na pin 1 w obd podac mase - ale tam jest 12 v nie chce tego robic bo boje sie o uszkodzenie auta ) no chyba ze ktos z was to juz robil i moze potwierdzic ten sposob lub podac jakas instrukcje jak to zrobic
na upartego warsztat gdzie za oplata mi zaprogramuja moze byc

[dawid27]

oczywiscie warsztaty ze slaska

[HarryAngel]

potlumacz sobie po swojemu

metod jest kilka

Keyless entry remote programming for Caravan 96

Follow the steps below

PREPPING:
1. Remove the upper dash panel to reveal the RKE Module
2. Unplug the RKE module (Some models have 2 plugs (ie. early Intrepids, eagles ect.)
3. Locate the GROUND & PROGRAM ENABLE WIRES. (Check forum for wire colors/location) these varies by year & model)

****Steps 3a, 3b & 3c IS OPTIONAL (For ease of FUTURE Programming)****
3a. Run a Double Conductor Wire (16 or 18 awg) from the RKE Module (in dash) to any location BELOW the dash panel or glove compartment for easy access.
3b. Splice one wire to the PROGRAM ENABLE wire and splice the other wire to the GROUND wire (THIS Ground Wire is PREFERED) on the RKE Module connector. (MARK which one is the PGM ENABLE WIRE at BOTH ENDS with tape or a marker)
3c. Below the dash connect a S.P.S.T. (Single Pole Single Throw) Toggle switch to the 2 wires. (Note which position is ON/CLOSED)

Programming an Initial RKE Remote
4.With Keyless Entry Remote(s) in hand Close ALL Doors insuring alarm is DISABLED (If appl.).
5. Turn the Iignition Key to the ON position (DO NOT START)
6. Ground the RKE Modules Program Enable Wire.
For those whom install the switch toggle it to the CLOSED or ON Position.
7. Press and hold the unlock button on ANY REMOTE and HOLD IT. (You will hear a chime)
8. Release the button and press it again (single press) on the 1st remote. (You MAY hear a chime again)
9. Press ANY Button on the next remote. This is #2 (You will hear a chime)
10. Press ANY button on additional remotes (IF NEEDED) (you will hear a chime)
11. When finished Turn the Ignition Key OFF
12. Remove the GROUND from the RKE Module's PROGRAM ENABLE Wire or turn the toggle switch off.
13. Test each remote to see if it works

NOTE: If there is a problem with programming you may need to:
a. Remove the GROUND from the RKE Modules PGM Enable wire BEFORE turning off the Ignition Key.
b. Ground the PGM Enable wire BEFORE turning ON the Ignition Key
c. After hearing the 1st chime imediatle press any key on the remote and once that chime is heard imeduiatly press any key on the next remote. ect.
d. Do NOT leave this terminal grounded! or the toggle switch ON/CLOSED

albo tutaj - matoda dla tego rodzaju pilota

http://www.ehow.com/how_7513656_program-remote-plymouth-voyager.html

[dawid27]

modul rke to ta kostka co jest na podszybiu po lewej stronie kolo glosnika ? bodajze kolor brazowy ?

[dawid27]

teraz wyczytuje na internecie ze ma byc caly modul podpiety ale jest problem zego u mnie nie ma o.O mam pusta wtyczke

[dawid27]

pomoze ktos ?