Windstar 2003-zamek szyfrowy nad klamką dzwi kierowcy

[luis]

Czy wiecie może gdzie znajdę kod zamka na dzwiach winiego? W schowku nie ma. Z innego forum dostałem taki tekst ale nie umiem go przetłumaczyć

"WindStar Keypad Code Location
1. Remove the U shaped trim panel at the bottom of the
dashboard area near the floor.
2. Behind the lower storage door area there is a vertical dash
frame member.
3. Attached on the back (engine side) of the member should
be the "brains" of the keyless entry.
It looks like the picture below:
4. Look for a square shaped electronic box about 3-4" square.
5. It should have an antenna lead plugged into it that looks
like the one on a car stereo.
6. Attached to this box - you will likely have to remove it/or
use a mirror - is a sticker with the default code.
On the
First picture the code is: 35737
The first is behind the center forward console. Remove the two screws and it pulls off.
There is a brace back there and there should be an electronic module bolted to it. Either
remove it or use a mirror so you can see the front of the module. A sticker may or may not
(it was missing on mine) that has the 5 digit factory door code on it.
The second place, that I haven't verified, but have read about, is in the same area as the
jack in the rear right corner of the van. The entire panel needs to come off, and an
electrnoic module is supposed to be in there that may have the code on it
If your van is like the 2001, the number for the keypad is located on the control box located
behind the right rear body panel.
here is info that I know works on my '96. I doubt your system is engineered much
differently: On my van: the module is located behind the center dash console near the floor.
I have a large "U" shaped trim piece that wraps around the lower center of the dash at the
floor. I removed that and found my module near the firewall at floor level. It has an
antenna cable plugged into it (antenna cable is exactly like the one in the back of a car
radio).
OK, looked behind the panel below the center console, nothing there. There are several
"computer modules", which one is the right one? and is it a sticker with a code on it, or a
scrap piece of paper taped on the thing? Why do they make things so darn difficult???
Behind that panel below the dash is where the module should be. It's bolted to the backside
of the brace. If you have a mirror and can read backwards, the code should be on a white
sticker attached to it, or you might have to unbolt it if the sticker is blocked by the brace.
On my '01, the sticker was gone. I haven't gone to the dealer yet. I wish I could get it for
$10 though. One dealer said it'd be $130 to do it. After writing to FoMoCo, they said most
dealers charge around $40.
Additional Information
Setting the new code
1. Erase any old codes by entering the factory code.(buttons will light up)
2. Press 1/2 button within 5 seconds.
3. Press 7/8 and 9/0 buttons at the same time within 5 seconds.
To set new code:
1. Enter factory code (numbers will light up)
2. Press 1/2 button within 5 seconds.
3. Enter personal 5 digit code(decide beforehand) within 5 seconds of each
previous one.
To unlock all the doors, press the 3/4 button within 5 seconds of the driver door
unlocking.
To lock all doors and set alarm system, press 7/8 and 9/0 at the same time.
To disarm or reset a triggered alarm, just enter personal or factory code.
Do not set a code with five of the same consecutive numbers. It's to easy for
thieves to figure out.
To enable or disable auto lock using the keyless entry keypad:
1. Enter the five-digit permanent entry code into the keyless entry keypad.
2. Within five seconds of entering the code, press and hold the 7/8 button on
the keypad.
3. Within five seconds of Step 2, and while holding the 7/8 button, press the
3/4 button on the keypad and release it.
4. Within five seconds of Step 3, release the 7/8 button on the keypad.
5. If the auto lock sound is disabled, the horn will chirp once. If the autolock
feature is enabled, the horn will chirp once shortly and then sound a second
time with a longer sound of the horn once the above sequence is completed.
Auto lock Enable/Disable
Using the Ignition Switch
1. Confirm that the perimeter alarm is disarmed.
2. Close all doors.
3. Confirm that the ignition switch is in the OFF position.
NOTE: Steps 4 through 8 must be performed within 30 seconds.
4. Turn the ignition switch from OFF to RUN.
5. Press the power door lock UNLOCK button three times.
6. Turn the ignition switch from RUN to OFF.
7. Press the power door lock UNLOCK button three times.
8. Turn the ignition switch from OFF to RUN.
9. Verify that the RAP module chirps the horn. This indicates that the RAP
module is now in the enable/disable mode and ready to accept program
changes.
10. Press the power door lock UNLOCK button one time to command the RAP
module to toggle the auto lock/relock feature OFF.
11. Press the power door lock LOCK button once to enter the command.
12. Verify that the horn chirps one time to signal the RAP module confirmation
of the command. There should only be one chirp indicating that auto
lock/relock feature has been disabled. If one chirp is heard, followed by a
longer sound of the horn, the auto lock/relock feature has just been enabled.
Return to step 10.
13. Turn the ignition switch to the OFF position to exit the enable/disable mode.
14. Exit the vehicle and verify that the RAP module chirps the horn once to
indicate that a feature has been changed and that auto lock/relock has been
disabled.
Use that code, or use it to enter your own -"


Proszę o pomoc gdzie znajdę kod lub o przetłumaczenie tekstu gdzie jest ten kod